Bench press calculator

Enter the weight and reps of a hard bench press set. You get your estimated bench max (1RM), the load for every percent, a rep table and a warm-up.

Man pressing a barbell on a flat bench, chest in orange, with a gauge near its maximum

Use a set you did to failure or within 1 rep of failure, with good form.

Estimated one-rep max
115 kg

Epley: 117.5 kg · Brzycki: 112.5 kg

Percent of your 1RM
PercentWeight
100%115 kg
95%110 kg
90%102.5 kg
85%97.5 kg
80%92.5 kg
75%85 kg
70%80 kg
65%75 kg
60%70 kg
55%62.5 kg
50%57.5 kg
Rep max estimates
RepsWeight
1115 kg
2110 kg
3105 kg
4102.5 kg
5100 kg
697.5 kg
795 kg
892.5 kg
987.5 kg
1085 kg
1182.5 kg
1280 kg
Warm-up before a heavy set
SetWeightReps
1 (40%)45 kg8
2 (55%)62.5 kg5
3 (70%)80 kg3
4 (80%)92.5 kg2
5 (90%)102.5 kg1

How to do a good test set

  1. Use a spotter or set the safety arms of the rack just below your chest. Do not test a heavy bench press alone without safeties.
  2. Pick a load you can lift 3 to 8 times. Warm up with the ladder below the result, then do one set close to failure.
  3. Lower the bar to touch your chest on every rep and press to straight arms. Reps that stop short of the chest give a high estimate.
  4. Keep your feet flat, your hips on the bench and your shoulder blades pulled back for the whole set.

Step-by-step form, the muscles it works and sets and reps: bench press guide.

What counts as a full rep

In a powerlifting meet, the bar must touch the chest, stay still for a moment until the "press" call, and then go up to straight arms with the head, shoulders and hips on the bench (IPF Technical Rulebook). Your gym bench is usually a touch-and-go rep, which most lifters find a little easier than a paused rep.

Compare like with like

  • Paused reps and touch-and-go reps give different numbers. Test the same way each time.
  • A wider grip shortens the range of motion. Keep the same grip width when you retest.
  • The formulas were built for the barbell bench press. Dumbbell and machine presses give a rougher estimate.

How the calculator works

It uses two public formulas and shows their average as the main result:

  • Epley: 1RM = weight × (1 + reps ÷ 30)
  • Brzycki: 1RM = weight × 36 ÷ (37 − reps)

The rep table runs the same formulas backward, and the percent chart rounds to 2.5 kg or 5 lb. To plan sets by effort instead of percent, use the RPE calculator. To load the bar, use the barbell plate calculator.

Questions

How accurate is a bench press calculator?

It is an estimate. Sets of up to about 10 reps taken close to failure give the best result. With more reps the error grows, so the calculator stops at 12. Use the result to plan your training loads, not as a record.

Should I test my true bench press max?

You do not need to. A hard set of 3 to 8 reps gives a useful estimate with less risk. If you test a true single, use a spotter or safety arms and stop the attempt when the bar slows down and your form changes.

Can I use dumbbell bench press numbers?

Only as a rough guide. The formulas come from barbell lifts, and two dumbbells are harder to balance than one bar, so most people lift less in total with dumbbells.

How often should I recalculate my bench max?

Every 4 to 8 weeks, or when your working sets clearly feel easier. Enter a new hard set and update your loads from the percent chart.

The Oh My Coach app

Train with a coach in your pocket

  • A voice coach that counts your reps and rest out loud
  • A weekly plan for your goal and the equipment you have
  • The same illustrated exercises as this site, with easier and harder versions

For iPhone. Your first 3 workouts are free.