Deadlift calculator

Enter the weight and reps of a hard deadlift set. You get your estimated deadlift max (1RM), loads for each percent, a rep table and a warm-up.

Man standing at the top of a deadlift, hips and hamstrings in orange, with a gauge

Use a set you did to failure or within 1 rep of failure, with good form.

Estimated one-rep max
115 kg

Epley: 117.5 kg · Brzycki: 112.5 kg

Percent of your 1RM
PercentWeight
100%115 kg
95%110 kg
90%102.5 kg
85%97.5 kg
80%92.5 kg
75%85 kg
70%80 kg
65%75 kg
60%70 kg
55%62.5 kg
50%57.5 kg
Rep max estimates
RepsWeight
1115 kg
2110 kg
3105 kg
4102.5 kg
5100 kg
697.5 kg
795 kg
892.5 kg
987.5 kg
1085 kg
1182.5 kg
1280 kg
Warm-up before a heavy set
SetWeightReps
1 (40%)45 kg8
2 (55%)62.5 kg5
3 (70%)80 kg3
4 (80%)92.5 kg2
5 (90%)102.5 kg1

How to do a good test set

  1. Pick a load you can pull 3 to 6 times. Long deadlift sets get sloppy, and a sloppy set gives a poor estimate.
  2. Warm up with the ladder below the result, then do one set close to failure.
  3. Set the bar down and reset your position before each rep. Bounced reps give a high estimate.
  4. End the set as soon as your lower back starts to round. There is no spotter for a deadlift, so your form is your safety check.

Step-by-step form, the muscles it works and sets and reps: deadlift guide.

What counts as a full rep

In a powerlifting meet, the lifter pulls the bar until standing straight with the knees locked and the shoulders back, and must not support the bar on the thighs on the way up (IPF Technical Rulebook). Count only reps that reach a full lockout.

Compare like with like

  • Sumo and conventional deadlifts load the body in different ways. Test with the stance you train with.
  • If your grip fails before your legs and back, the result shows your grip, not your deadlift. Use chalk or a mixed grip for the test set, and keep the same grip each time.
  • Trap bar deadlifts and Romanian deadlifts are different lifts. Use this result for the barbell deadlift only.

How the calculator works

It uses two public formulas and shows their average as the main result:

  • Epley: 1RM = weight × (1 + reps ÷ 30)
  • Brzycki: 1RM = weight × 36 ÷ (37 − reps)

The rep table runs the same formulas backward, and the percent chart rounds to 2.5 kg or 5 lb. To plan sets by effort instead of percent, use the RPE calculator. To load the bar, use the barbell plate calculator.

Questions

How many reps should I use to estimate my deadlift max?

A set of 3 to 6 reps works best. The formulas accept up to 12 reps, but long deadlift sets often end because of fatigue in the grip or lower back, not the main muscles.

Does sumo or conventional give a higher max?

It depends on the person. The two styles use the hips, knees and back in different ways. Test with the style you train, and keep it the same each time.

Can I use touch-and-go reps?

You can, but they give a higher estimate than reps with a reset on the floor. Use the same style each time you test.

Can I use this for the trap bar deadlift?

The formulas work for any barbell lift, so the result is your trap bar max. It is not the same as your straight-bar deadlift max.

The Oh My Coach app

Train with a coach in your pocket

  • A voice coach that counts your reps and rest out loud
  • A weekly plan for your goal and the equipment you have
  • The same illustrated exercises as this site, with easier and harder versions

For iPhone. Your first 3 workouts are free.