Squat calculator

Enter the weight and reps of a hard back squat set. You get your estimated squat max (1RM), working weights by percent, a rep table and a warm-up.

Man at the bottom of a barbell back squat in a rack, legs in orange, with a gauge

Use a set you did to failure or within 1 rep of failure, with good form.

Estimated one-rep max
115 kg

Epley: 117.5 kg · Brzycki: 112.5 kg

Percent of your 1RM
PercentWeight
100%115 kg
95%110 kg
90%102.5 kg
85%97.5 kg
80%92.5 kg
75%85 kg
70%80 kg
65%75 kg
60%70 kg
55%62.5 kg
50%57.5 kg
Rep max estimates
RepsWeight
1115 kg
2110 kg
3105 kg
4102.5 kg
5100 kg
697.5 kg
795 kg
892.5 kg
987.5 kg
1085 kg
1182.5 kg
1280 kg
Warm-up before a heavy set
SetWeightReps
1 (40%)45 kg8
2 (55%)62.5 kg5
3 (70%)80 kg3
4 (80%)92.5 kg2
5 (90%)102.5 kg1

How to do a good test set

  1. Squat inside a rack with the safety pins set just below your lowest position. You can then drop the bar on the pins if a rep fails.
  2. Pick a load you can squat 3 to 8 times. Warm up with the ladder below the result, then do one set close to failure.
  3. Reach the same depth on every rep. Higher reps give a higher estimate, so a set with shallow reps overstates your max.
  4. Stop the set when your back rounds or your knees cave in. A rep with broken form does not count.

Step-by-step form, the muscles it works and sets and reps: barbell back squat guide.

What counts as a full rep

In a powerlifting meet, the top of the legs at the hip joint must go lower than the top of the knees, and the lifter must stand back up to straight knees (IPF Technical Rulebook). Many gym squats stop higher than this. Your estimate is for the depth you use in the test set.

Compare like with like

  • High-bar and low-bar squats move different loads for most people. Test with the bar position you train with.
  • A lifting belt or knee sleeves can change the number. Test with the same gear each time.
  • Front squats and box squats are different lifts. Use this result for the back squat only.

How the calculator works

It uses two public formulas and shows their average as the main result:

  • Epley: 1RM = weight × (1 + reps ÷ 30)
  • Brzycki: 1RM = weight × 36 ÷ (37 − reps)

The rep table runs the same formulas backward, and the percent chart rounds to 2.5 kg or 5 lb. To plan sets by effort instead of percent, use the RPE calculator. To load the bar, use the barbell plate calculator.

Questions

How deep do I need to squat for the calculator?

As deep as you squat in training, on every rep. The estimate is for that depth. If you want a number you can compare with powerlifting results, squat until the hip crease is below the top of the knee.

Should I test my squat max without a spotter?

Only inside a rack with safety pins at the right height. Without a rack, use a spotter you trust and a lighter test set of 5 to 8 reps.

Can I use the calculator for the front squat?

You can use the formulas for any barbell lift, but the result is your front squat max, not your back squat max. Most people front squat less than they back squat.

Does a belt change my squat max?

For many lifters, yes, a little. It does not matter which you choose, as long as you test and train the same way.

The Oh My Coach app

Train with a coach in your pocket

  • A voice coach that counts your reps and rest out loud
  • A weekly plan for your goal and the equipment you have
  • The same illustrated exercises as this site, with easier and harder versions

For iPhone. Your first 3 workouts are free.